- 6,800 m² across two buildings in Hengli Town, Dongguan — production, inspection, and engineering under one roof.
- ISO 9001:2015 / IATF 16949:2016 / ISO 14001:2015 — certificate numbers published and verifiable.
- Stainless Steel: The defining machining problem is work hardening combined with low thermal conductivity.
- Grades in regular use: 303 for free-machining work, 304 and 316L for corrosion resistance, 17-4 PH where strength is needed after ageing, 416 and 420 where hardness is required.
- Incoming stock is verified against the mill certificate before it is cut.
What makes stainless steel behave differently under the tool?
The defining machining problem is work hardening combined with low thermal conductivity. Heat does not leave with the chip, so it stays in the cutting zone; the surface layer work-hardens, and the next pass cuts through hardened material, which accelerates tool wear. The practical response is to keep the tool cutting rather than rubbing — maintain chip load, avoid dwelling, and do not take a finishing cut so light that it burnishes instead of shears.
Confirm the grade on the mill certificate by XRF before cutting — 304 and 316 look identical and behave differently in service.
Dimensional behaviour of stainless steel
Dimensional stability is good once the part has stopped moving, but thin walls distort from the residual stress released by removing stock. Stress-relieving between roughing and finishing is the standard response on a tight-tolerance thin-wall part.
The general rule for your part is that a tolerance is held by the process, not by the machine. Where a feature is tight, the finishing pass is separated from roughing, the part is allowed to stabilise, and the measurement is taken at a controlled temperature.
What finishing and surface treatment apply to stainless steel?
Passivation after machining restores the chromium oxide layer that free iron from cutting tools has contaminated.
You specify finishing on the drawing, not assume it at the end. Where a coating adds thickness, threaded and press-fit features need the allowance stated, because a coating applied after inspection changes the fit.
What does stainless steel do to tooling and cycle time?
Heat does not leave with the chip, so it stays in the cutting zone; the surface layer work-hardens, and the next pass cuts through hardened material, which accelerates tool wear.
The lever that matters most for you is usually design rather than process: pocket depth, corner radius, and wall thickness change cycle time more than any tooling choice, because they determine the tool that can be used and therefore how much material can be removed per minute.
Where the money is actually decided
The design levers on stainless are wall thickness and pocket depth. Thin walls distort as roughing releases residual stress, so a stress-relief operation and a separate finishing pass are usually cheaper than trying to hold a thin wall in one go. Avoiding a dwell — a tool rubbing rather than cutting. Matters more here than on any other common material.
This is cheaper to settle at quote time than once parts already exist, because the changes are usually trivial on the drawing and significant on the machine.
What is the certification position?
ISO 9001:2015, IATF 16949:2016 (excluding clause 8.3 product design), and ISO 14001:2015. Each with a certificate number verifiable with the registrar.
What tolerance applies?
±0.003 mm on CNC milling, ±0.002 mm on CNC turning; ±0.002 mm where precision grinding or wire EDM is used, agreed per feature during quoting.
Grade selection for stainless steel
Austenitic, martensitic, and precipitation-hardening stainless grades are the grades that come up in practice. 303 for free-machining work, 304 and 316L for corrosion resistance, 17-4 PH where strength is needed after ageing, 416 and 420 where hardness is required.
Your grade selection is usually settled by the service environment, corrosion, strength, or temperature, and only then by machinability. If you choose on machinability first, your part meets the drawing and fails in service.
Who is on the other side of the purchase order?
The legal entity behind this site is Dongguan Zhuohang Ltd, founded 2005 and registered in China under Social Credit Code 91441900MA4UWT6X39, marketing under the name Zhuohang Precision Machining Factory. Its registered and production address is No. 8, Shuibian Songyuan Road, Hengli Town, Dongguan, Guangdong, China 523470.
Use the National Enterprise Credit Information Publicity System and the 18-character code to verify a Chinese manufacturer. Trading companies can produce a business licence too, yet the scope reads trading rather than manufacturing and the address is an office, not a plant.
What capacity sits behind this?
Total machine count is not the question, the question is how many machines sit in the family that makes your part, because that is the queue your part waits in. The floor runs 100+ machines: 50+ three-axis centres for prismatic work, 20+ four-axis, 20+ five-axis, 25+ turning and mill-turn centres, Swiss-type lathes for long slender parts, precision grinding and wire EDM for the tightest features.
Having several machines in that family is what lets a part re-route rather than queue when a machine is pulled for service. That, not the headline machine, is what protects a delivery date.
Why the material decision comes first
On a CNC turning service part, the material is the single biggest lever on the price, the tolerance and the lead time, so it should be decided before the drawing is frozen. Aluminium machines fast and cheap and suits light, non-structural parts. Steel and stainless add strength and corrosion resistance at a higher machine cost. Titanium and Inconel hold high-temperature strength but run many times slower and wear tooling fast. If you pick the material for the service - the load, the environment, the temperature - you get a part that works and a quote that is honest, instead of paying for an alloy the part never needed.
Specifying the grade, not just the name
The material name is not enough; the grade is the specification. Aluminium 6061-T6 and 7075-T6 are different strengths, and stainless 303 and 316 are different jobs. The grade, the temper and the condition all belong on the drawing, and the mill certificate confirms them. Incoming stock here is verified against the mill certificate before it is cut - composition by XRF, hardness where specified. Contact Felipe Iglesias at [email protected] or +86 13126536955 with the material and the grade, and the quote reflects the real stock.
The evidence behind the numbers
Ask for proof and the answer is specific: Dongguan Zhuohang Ltd runs 100+ CNC machines on a 6,800 m² floor in Hengli Town, Dongguan, including the Mazak VARIAXIS I-600 five-axis, the INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes. Inspection runs on a Hexagon CMM with the 10:1 gauge rule, and ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015 are held by verifiable certificate number. Critical characteristics are tracked with Ppk 1.67 initial and Cpk 1.33 in production - a tolerance quoted here is a tolerance held.
Buyers across Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa are served from Dongguan with worldwide shipping. MOQ is 1 piece; lead times run about 3 / 7 / 30 days. Send the drawing and quantity to Felipe Iglesias at [email protected] or +86 13126536955 and the quote returns with the process spelled out.
Starting your order
The quickest route to a part is a model and a quantity. Send the STEP or IGES file with a 2D drawing that names the tolerances, datums, material grade and finish, plus the quantity and the lead time you need, and you get an itemised quote - material, setup, cycle time and inspection - not a round figure. No finished drawing? Send what you have and the questions that are blocking you; the goal is to begin, not to wait for a flawless package.
Email Felipe Iglesias at [email protected] or call +86 13126536955. MOQ is 1 piece, lead times run roughly 3 / 7 / 30 days, and shipping covers Europe, the Americas, Asia, Oceania and Africa, plus worldwide from Dongguan.
De-risking a first order
A trial order of a few pieces is the cheapest insurance you can buy — it proves the routing, the tolerance and the paper trail on a small batch before the volume order locks in. One floor, one quality system, one accountable party, whether the run is a single part or a full production lot, so what the trial confirms is what production repeats.
What this shop actually runs
If you ask for capability evidence, you deserve a specific answer. This facility operates 100+ CNC machines across 6,800 m2 in Dongguan, China, staffed by 100+ people. The machines, listed by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Set up for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Set up for prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Set up for long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Set up for shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Set up for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance bands: ±0.003 mm milled, ±0.002 mm turned, ±0.002 mm ground or wire-cut. Capability indices: Ppk >= 1.67 at the initial study; Cpk >= 1.33 ongoing in production.
Certifications: ISO 9001:2015 (116024/A/0001/UK/En) · IATF 16949:2016 (131941/A/0001/SM/En, design clause 8.3 excluded) · ISO 14001:2015 (116024/B/0001/UK/En), held by Dongguan Zhuohang Ltd (USCC 91441900MA4UWT6X39, since 2005).
Service area: we supply Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, with worldwide delivery from China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Send a drawing and get a manufacturability read
Upload your model for a quote, or arrange a factory audit with [email protected] or +86 13126536955. Ask for Felipe Iglesias.
Frequently Asked Questions
Do you sign NDAs before reviewing drawings?
Yes. Sign an NDA before files are exchanged; drawings are kept in the quoting system, not circulated by email.
What happens if the first article does not conform?
In short, The nonconformance is documented and the corrective action is agreed before any further parts are made. Whether the replacement cost sits with the plant or the customer depends on where the deviation came from, which is why the revision and the drawing standard are confirmed in writing at the start.
Does stainless steel cost more to machine than aluminium?
Usually yes, and the reason differs by material: for titanium it is cutting speed and tool consumption, for stainless it is cycle time and work-hardening management. The lever that matters most is usually design depth rather than process choice.
What is the difference between a prototype build and a production build here?
Usually only quantity and scheduling. Both run on the same machines and the same process, which is what makes a later ramp a scheduling change rather than a re-qualification.
What tolerances can you hold?
In short, ±0.003 mm on CNC milling, ±0.002 mm on CNC turning, and ±0.002 mm where precision grinding or wire EDM is used. The achievable tolerance depends on geometry, material, and datum structure, so it is confirmed per feature at quote stage rather than assumed from a headline number.
Which markets do you export to?
In short, Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa. Our service area also spans Europe, the Americas, Asia, Oceania and Africa — based in China, we serve customers worldwide.
Do you certify stainless steel material?
Yes. Material certificates are supplied with the parts and incoming stock is checked against the mill certificate — composition by XRF, hardness where specified. Traceability is per heat or per batch as the certificate defines it.
Continue reading: 3 Axis CNC Turning Service · 4 Axis CNC Turning Service · 5 Axis CNC Turning Service
Standards referenced on this page
- ASTM A276/A276M-17 — Standard Specification for Stainless Steel Bars and Shapes
- ASTM A484/A484M-24 — Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
- ISO 9001 — Quality management systems — Requirements